Easily get the latest Cisco CCNA Wireless 200-355 dumps, “Implementing Cisco Wireless Networking Fundamentals (WIFUND)” 200-355 Exam.
You can upgrade your skills by downloading the 200-355 pdf or the online 200-355 exam exercise test! 99.5% pass rate: leads4pass.com
Table of Contents:
- Latest Nicky Cisco CCNA Wireless 200-355 pdf
- Latest Cisco CCNA Wireless 200-355 Practice Questions and Answers
- Latest Cisco CCNA Wireless 200-355 YouTube videos:
- Related 200-355 Popular Exam resources
- Lead4pass Promo Code 12% Off
- Why Choose Lead4pass?
Latest Nicky Cisco CCNA Wireless 200-355 pdf
[PDF] Free Cisco CCNA Wireless 200-355 pdf dumps download from Google Drive: https://drive.google.com/open?id=1u_DoAVC9ga0qwuXhJFp0EzKumxQKV5N2
[PDF] Free Full Cisco pdf dumps download from Google Drive: https://drive.google.com/open?id=1CMo2G21nPLf7ZmI-3_hBpr4GDKRQWrGx
200-355 WIFUND – Cisco: https://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/wifund.html
Latest Cisco CCNA Wireless 200-355 Practice Questions and Answers
QUESTION 1
A WLAN deployment uses a combination of Cisco Aironet 1260 APs and multiple Cisco 5500 Wireless LAN Controllers
to provide wireless LAN access to end- users. The network administrator has decided to use DHCP Option 43 to enable
the APs to discover the wireless LAN controllers. When configuring the DHCP scope, which format should be used for
the Cisco WLC addresses?
A. a comma-separated ASCII string of Cisco WLC AP-manager addresses
B. a comma-separated ASCII string of Cisco WLC management addresses
C. a comma-separated ASCII string of Cisco WLC virtual IP addresses
D. a hexadecimal string of Cisco WLC AP-manager addresses
E. a hexadecimal string of Cisco WLC management addresses
F. a hexadecimal string of Cisco WLC virtual IP addresses
Correct Answer: E
Complete these steps in order to configure DHCP Option 43, in the embedded Cisco IOS DHCP server, for all Cisco
Aironet APs that run Cisco IOS. This includes all APs except for the VxWorks 1000 Series (see the next section) and
the
600 Series OEAP which does not use Option 43. IP DHCP pool
network
default-router
DNS-server
option 43 hex
The hexadecimal string in step 3 is assembled as a sequence of the TLV values for the Option 43 suboption: Type +
Length + Value. Type is always the sub-option code 0xf1. Length is the number of controller management IP addresses
times 4 in hex. Value is the IP address of the controller listed sequentially in hex.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/97066-dhcp-option-43-00.html
QUESTION 2
A Cisco Aironet 1260 AP is unable to join a Cisco 2500 Series WLC that is connected through a Layer 2 switch.
Which three options help to verify the wireless network operation and locate a possible issue? (Choose three.)
A. Verify the status of GUI Wireless > Country
B. Verify the status of GUI Wireless > Timers
C. Verify the status of GUI WLANs > ID > Advanced
D. CLI debug of dot11
E. CLI debug of DHCP
F. Verify the Cisco WLC license
G. Verify Cisco WLC model
Correct Answer: AEF
See reference link below for troubleshooting.
“Troubleshoot a Lightweight Access Point Not Joining a Wireless LAN Controller”
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/99948-lap-notjoin-wlc-tshoot.html#topic1
QUESTION 3
A lightweight AP has been deployed in local mode in a network that consists of 10 wireless LAN controllers in a single
mobility group. The AP has been configured to use primary, secondary, and tertiary Cisco WLCs. Due to a major power
failure, all those Cisco WLCs are unavailable.
Which step does the AP take next?
A. The AP reboots and repeatedly attempts to join the configured primary, secondary, and tertiary Cisco WLCs in that
order. The process continues until one of the configured Cisco WLCs is available.
B. The AP attempts to join a Cisco WLC configured as a master controller.
C. The AP attempts to join the Cisco WLC that has the greatest capacity available.
D. The AP state transitions to AP Fallback Mode and continues to provide limited WLAN services (that is, no new client
authentications) until a Cisco WLC is available.
Correct Answer: B
If a WLC is configured as a Master Controller, the LAP selects that WLC and sends it an LWAPP join request.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/70333-lap-registration.html
QUESTION 4
Refer to the exhibit. Which command was given in the wireless controller to display the active clients that are associated
with an access point?
A. show ap clients
B. show client active all
C. show 802.11 association
D. show client summary
Correct Answer: D
QUESTION 5
Refer to the exhibit.
A customer has set up an autonomous access point with a single broadcast SSID on the 2.4-GHz radio and requested
that an engineer adds an additional SSID to the 2.4-GHz radio. Given the output, what should be configured to implement
the new SSID?
A. the new SSID on the 5-GHz radio
B. dot11 mbssid globally and mbssid mode under the SSIDs
C. guest-mode on the dot11 radio interface
D. guest-mode under the new SSID
Correct Answer: B
QUESTION 6
Refer to the exhibit. A network administrator is attempting to connect to the GUI of a WLC with interfaces as shown.
Which IP address should the network administrator use?
A. 192.168.0.2
B. 192.168.1.2
C. 192.168.2.2
D. 192.168.3.2
E. 192.168.4.2
Correct Answer: B
QUESTION 7
Refer to the exhibit. Based on the diagram, what two design requirements must be met? (Choose two.)
A. WGB is Autonomous
B. WGB is Universal
C. WGB can be Autonomous or Universal
D. Upstream AP is Aironet
E. Upstream AP is not Aironet
F. Upstream AP can be any make/model
Correct Answer: AD
QUESTION 8
During an upgrade, the wireless infrastructure has seen a few access points join and then drop off the network. After
further investigation, it appears the access points may have an IOS code version that is causing issues. Where in the
controller is this information found?
A. GUI > Wireless > Access Point > General
B. CLI > show ap image all
C. GUI > Monitor > Software Version
D. CLI > show sysinfo
Correct Answer: A
QUESTION 9
Refer to the exhibit. When the Admin Status of an access point is enabled, what does this mean in radios?
A. 802.11a/n/ac and 802.11b/g/n radios must be UP.
B. 802.11a/n/ac and 802.11/b/g/n radios can be UP or DOWN.
C. 802.11a/n/ac is DOWN, but the 802.11b/g//n radio is UP by default.
D. 802.11a/n/ac is UP, but the 802.11b/g/n radio is DOWN by default.
Correct Answer: B
QUESTION 10
When using Cisco WCS version 7.0, which two features are available for the client troubleshooting tool when a Cisco
Does Compatible Extensions v5 wireless client gets connected? (Choose two.)
A. Request CleanAir reports from the client
B. Send text messages to the client
C. Aggregated Cisco ACS authentication client information
D. Request the client to ping the DHCP-supplied IP gateway
E. Display a summary of client event history
Correct Answer: BD
QUESTION 11
Which two statements about the requirements to configure inter-controller roaming are true? (Choose two.)
A. The same mobility domain names are configured across controllers.
B. The same RF group names are configured across controllers.
C. The same controller hardware version is configured across controllers.
D. The same AP-manager interface is configured across controllers.
E. The same virtual interface is configured across controllers.
F. The same controller software version is configured across controllers.
Correct Answer: AE
All controllers must be configured with the same mobility group name. All controllers must be configured with the same
virtual interface IP address. If necessary, you can change the virtual interface IP address by editing the virtual interface
name on the Controller > Interfaces page.
If all the controllers within a mobility group are not using the same virtual interface, inter-controller roaming may appear
to work, but the handoff does not complete, and the client loses connectivity for a period of time.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-0/configuration/guide/c70/c70mobil.html
QUESTION 12
A customer wants to implement a policy on a guest WLAN, in which clients must accept the company wireless policy
and enter an email address to access the guest network. The company does not have access to RADIUS servers and
wants the WLAN to use open Layer 2 security. Which Layer 3 security web policy must be enabled to meet these
criteria?
A. authentication
B. web authorization on MAC filter failure
C. conditional web redirect
D. web pass-through
Correct Answer: D
QUESTION 13
Which protocol is used for Cisco WCS to communicate with Cisco WLC?
A. SNMP
B. CAPWAP
C. HTTPS
D. SSH
Correct Answer: A
Explanation/Reference:
WCS simplifies controller configuration and monitoring and reduces data entry errors. WCS uses the industry-standard
SNMP protocol to communicate with the controllers. WCS also includes the Floor Plan editor which allows you to do the
following:
Vectorize bitmapped campus, floor plan, and outdoor area maps.
Add and change wall types.
Import the vector wall format maps into the database.
Latest Cisco CCNA Wireless 200-355 YouTube videos:
We offer more ways to make it easier for everyone to learn, and YouTube is the best tool in the video. Follow channels: https://www.youtube.com/channel/UCXg-xz6fddo6wo1Or9eHdIQ/videos get more useful exam content.
All of our exam dumps are updated throughout the year, follow us! Get the latest recommendations! Pass the Cisco CCNA Wireless 200-355 exam We recommend: https://www.leads4pass.com/200-355.html (564 Q&A).
Related 200-355 Popular Exam resources
| title | youtube | 200-355 WIFUND – Cisco | lead4pass | Lead4Pass Total Questions | |
|---|---|---|---|---|---|
| Cisco 200-355 | lead4pass 200-355 dumps pdf | lead4pass 200-355 youtube | 200-355 WIFUND – Cisco | https://www.leads4pass.com/200-355.html | 641 Q&A |
| Cisco CCNA Wireless | https://www.leads4pass.com/640-722.html | 277 Q&A |
Lead4pass Promo Code 12% Off
Why Choose Lead4pass?
Lead4Pass helps you pass the exam easily! We compare data from all websites in the network, other sites are expensive,
and the data is not up to date, Lead4pass updates data throughout the year. The pass rate of the exam is above 98.9%.
